× Close Pozor! Tyto specifikace se vztahují k výchozí konfiguraci produktu. Networking Interface: 1 x 10/100/1000 Ethernet port Processor Specs: Atheros MIPS 74Kc, 560 MHz The TDMA airMAX protocol enables unprecedented scalability, high throughput and low latency in unlicensed, multipoint networks. Ubiquiti’s airMAX technology is proven in millions of deployments worldwide, exhibiting outstanding performance in outdoor environments. Both near-field plots are displayed in watts and use a linear scale. The integrated isolator design improves RF isolation to spatially filter out interference, and the metal-plated interior of the rear housing enhances RF shielding.Ĭompare the two near-field plots, and note the superior performance of the integrated RF isolator. Incorporating advanced engineering with proprietary airMAX technology, the PowerBeam M5 ISO is ideal for deployments requiring maximum performance and RF isolation. × Close Pozor! Tento popis se vztahuje k výchozí konfiguraci produktu. Vertical pole, Pendant and Corner mounts.Antenna types not included in this list or having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. This radio transmitter FCC ID: SWX-PBE5M / IC: 6545A-PBE5M has been approved by FCC / ISED Canada to operate with the antenna types listed below with the maximum permissible gain for each antenna type indicated. Output power is adjusted to compensate for loss between the radio and the antenna. Compare Ubiquiti Networks PBE-M5-400 PowerBeam airMAX Bridge 5-Pack vs Ubiquiti Networks LBE-M5-23 LiteBeam M5 with InnerFeed Technology vs Ubiquiti Networks airMAX PowerBeam AC 5 GHz Gen2 High Performance Bridge. Cable Loss (When applicable)Įnter the cable loss in dB. Note the requirements and antenna types listed below. If Calculate EIRP Limit is enabled, transmit output power is automatically adjusted to comply with the regulations of the applicable country. Installer Compliance Responsibilityĭevices must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements. Setup using the UISP ™ app requires the U-Installer, sold separately. You can also manage your device using the Ubiquiti Internet Service Provider Application. For details, refer to the User Guide available at ui.com/download/airmax The airOS Configuration Interface will appear, allowing you to customize your settings as needed. You must agree to the Terms of Use to use the product. Enter ubnt in the Username and Password fields.Launch your web browser and type in the address field.Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.Make sure that your host system is connected via Ethernet to the device.Verify connectivity in the airOS Configuration Interface. The PowerBeam mounted outdoors without the Reflector installed provides outdoor-to-indoor coverage using the 3 dBi Antenna Feed only. The PowerBeam mounted outdoors with the Reflector installed provides directional outdoor coverage (gain is reflector-dependent). The Power LED will light green when the device is connected to a power source. The Ethernet LED will light steady green when an active Ethernet connection is made and flash when there is activity. In airOS®, you can modify the threshold values for the wireless signal strength LEDs on the Advanced tab under Signal LED Thresholds. If you need to remove the Antenna Feed, you must depress the Release button first. This ensures that the Antenna Feed is locked into place. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the Gigabit PoE adapter.Īfter you assemble the device, check the Release button it should be fully engaged in the Release Button Slot of the Rear Housing. To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. For more details, visit ui.com/toughcable Hardware Overview We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE.* The PBE-M5-400 Antenna Feed has a thin gray ring around the center of the cap to differentiate it from the PBE-M5-300 Antenna Feed.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |